We – EPG Group the largest agricultural gearbox and pto manufacturing facility in China with five distinct branches. For much more specifics: Cell/whatsapp/telegram/Kakao us at: 0086-13083988828
Slip clutch: this variety makes use of a slip clutch on the pushed conclude yoke which is comprised of three steel plates in line held jointly with a sequence of bolts with springs below the nuts. The notion right here is that when you tighten the nuts the pressure is improved onto the centre plate which when set up for the load will permit the shaft to turn and the put into action to stall, absorbing the shock load. As mine is rated from twenty-forty hp and I’m working a 17 hp I experienced to make alterations to established it up. Via trial and mistake I decided that I experienced to remove half the tension bolts and springs and back again off the remainder nuts to bare minimum in order for the clutch to “slip” prior to stall on the tractor. Near up of two yokes with the common joint. Notice the slight oozing of grease from the UJ seal ends, the clump of grease is from within the yoke splined shaft location –Generate (outer) yoke has a feminine (usual spline) gap and “Y” form finish that is the universal joint (UJ) mount. –UJ is a cross formed casting obtaining roller bearings enclosed with caps at all 4 factors and is held into the yoke with four “C” clips –Interior yoke and drive shaft is yet another yoke welded to the travel end, of the travel shaft. –Pushed shaft and interior yoke is the driven shaft that rides inside of of the generate shaft and has a yoke welded at the pushed finish –UJ yet another UJ as abovehyundai accent travel shaft cost EPG travel shaft grand livina manufacturer 2004 dodge ram 1500 rear travel shaft rotocultivator jeep wrangler push shaft ploughshares 2006 chrysler pacifica push shaft in bush hog 2615 pto shaft T. pto shaft will not likely extend line e39 driveshaft were tractor pto shaft diameter selected rhino bush hog dealers as the Nationwide Rotary Tillage Equipment Business “Best Manufacturer Products” in 2007 by Rotocultivator Branch of China Agricultural Machinery Industry Affiliation. EPG specializing in the manufacture of rotocultivator ploughshares and other non-standardized farm machinery reducing tools.
Backyard Resources three Level Flail Mower Lawn Mower For Tractor
Flail mower offer an efficient answer for the management of abnormal growth. PTO flail mower, also recognized as mulching mowers, are developed to mow and shred concurrently. The shredded materiall functions as an efficient mulch, to retard ensuing progress even though delivering a medium that will better release vitamins and minerals into the soil.
| Lift Obligation Flail Mower | ||||||||||
| Product | EF85 | EF95 | EF105 | EF115 | EF125 | EF135 | EF145 | EF155 | EF165 | EF175 |
| Construction weight(kg) | one hundred | 115 | a hundred thirty | 145 | 160 | one hundred seventy five | 190 | 210 | 235 | 255 |
| Chopping width(mm) | 829 | 929 | 1029 | 1129 | 1229 | 1329 | 1429 | 1529 | 1629 | 1729 |
| PTO speed | 540r/min | |||||||||
| Flail kind | Y blade / Hammer | |||||||||
| Quantity of flails | thirty | thirty | 36 | 42 | forty two | forty eight | 54 | 54 | 54 | 60 |
| Tractor HP | fourteen-18 | 16-20 | 20-30 | 20-30 | twenty five-35 | twenty five-35 | twenty five-35 | 30-forty | 30-forty | thirty-forty |
| Middle Duty Flail Mower | ||||||||||
| Design | EFG105 | EFG115 | EFG125 | EFG135 | EFG145 | EFG155 | EFG165 | EFG175 | ||
| Construction weight(kg) | 230 | 245 | 257 | 272 | 287 | 302 | 317 | 329 | ||
| Slicing width(mm) | 1020 | 1120 | 1220 | 1320 | 1420 | 1520 | 1620 | 1720 | ||
| PTO pace | 540r/min | |||||||||
| Flail kind | Y blade / Hammer | |||||||||
| Number of flails | Y blade:32 Hammer:16 |
Y blade:forty Hammer:20 |
Y balde:forty Hammer:twenty |
Y blade:forty eight Hammer:24 |
Y balde:48 Hammer:24 |
Y blade:forty eight Hammer:24 |
Y blade:fifty six Hammer:28 |
Y balde:56 Hammer:28 |
||
| Tractor HP | fifteen-20 | fifteen-20 | 15-20 | 18-twenty five | 20-30 | twenty-thirty | 25-35 | thirty-35 | ||
| Center Obligation Flail Mower | |||||||||||
| Model | EFGC105 | EFGC115 | EFGC125 | EFGC135 | EFGC145 | EFGC155 | EFGC165 | EFGC175 | EFGC185 | ||
| Framework bodyweight(kg) | 250 | 265 | 277 | 292 | 317 | 322 | 347 | 359 | 385 | ||
| Slicing width(mm) | 1020 | 1120 | 1220 | 1320 | 1420 | 1520 | 1620 | 1720 | 1820 | ||
| PTO velocity | 540r/min | ||||||||||
| Flail variety | Y blade / Hammer | ||||||||||
| Quantity of flails | Y blade:32 Hammer:sixteen |
Y balde:40 Hammer:twenty |
Y balde:40 Hammer:twenty |
Y balde:forty eight Hammer:24 |
Y blade:forty eight Hammer:24 |
Y blade:48 Hammer:24 |
Y blade:fifty six Hammer:28 |
Y blade:fifty six Hammer:28 |
Y blade:64 Hammer:32 |
||
| Tractor HP | eighteen-twenty five | eighteen-25 | 18-twenty five | 20-30 | 20-30 | thirty-forty | 35-forty five | 40-fifty | 45-eighty five | ||
| Heavy Obligation Flail Mower | |||||||||||
| Model | EFGCH105 | EFGCH115 | EFGCH125 | EFGCH135 | EFGCH145 | EFGCH155 | EFGCH165 | EFGCH175 | EFGCH185 | ||
| Framework bodyweight(kg) | 285 | 300 | 312 | 327 | 352 | 332 | 347 | 359 | 385 | ||
| Reducing width(mm) | 1020 | 1120 | 1220 | 1320 | 1420 | 1520 | 1620 | 1720 | 1820 | ||
| PTO velocity | 540r/min | ||||||||||
| Flail type | Y blade / Hammer | ||||||||||
| Variety of flails | Y blade:32 Hammer:sixteen |
Y balde:forty Hammer:twenty |
Y balde:forty Hammer:20 |
Y balde:forty eight Hammer:24 |
Y blade:forty eight Hammer:24 |
Y blade:48 Hammer:24 |
Y blade:56 Hammer:28 |
Y blade:fifty six Hammer:28 |
Y blade:sixty four Hammer:32 |
||
| Tractor HP | 18-28 | eighteen-28 | twenty-28 | twenty five-35 | twenty five-35 | 30-40 | 35-55 | 35-55 | 35-55 | ||
| Middle Duty Bush Cutter | |||||||||||
| Model | AG140 | AG170 | AG200 | AG220 | |||||||
| Framework bodyweight(kg) | 320 | 390 | 430 | 480 | |||||||
| Reducing width(mm) | 1380 | 1680 | 1980 | 2180 | |||||||
| PTO pace | 540r/min | ||||||||||
| Flail type | Hammer | ||||||||||
| Variety of flails | twelve | 19 | eighteen | 20 | |||||||
| Tractor HP | 35-forty five | forty-fifty | 45-sixty | 55-eighty five | |||||||
| Large Responsibility Bush Cutter | |||||
| Product | AGF140 | AGF160 | AGF180 | AGF200 | AGF220 |
| Dimension(mm) | 1800x2225x1020 | 2000x2225x1020 | 2200x2225x1020 | 2400x2225x1020 | 2600x2225x1020 |
| Construction bodyweight(kg) | 598 | 612 | 658 | 698 | 738 |
| Slicing width(mm) | 1400 | 1600 | 1800 | 2000 | 2200 |
| PTO pace | 540r/min | ||||
| PTO spline | 6x8x1600mm | ||||
| Tractor HP | 40-85 | 50-85 | fifty five-90 | 55-90 | fifty-90 |
| Large Responsibility Bush Cutter | |||||
| Model | AGFK140 | AGFK160 | AGFK180 | AGFK200 | AGFK220 |
| Slicing width(mm) | 1400 | 1600 | 1800 | 2000 | 2200 |
| Get to angle up | 90° | ||||
| Reach angle down | 55° | ||||
| PTO | 540r/min | ||||
| Tractor HP | 30-forty | 40-sixty | 50-70 | sixty-ninety | |
| Light-weight Responsibility Bush Cutter | |||
| Design | AGL120 | AGL145 | AGL165 |
| Construction fat(kg) | 250 | 280 | 315 |
| Tilt-up angle | 90° | ||
| Tilt-down angle | 55° | ||
| Cutting width(mm) | 1200 | 1400 | 1600 |
| Flail variety | Y blade / Hammer | ||
| Number of flails | Hammer:20/Y blade:40 | Hammer:24/Y blade:forty eight | Hammer:28 |
| PTO velocity | 540r/min | ||
| Tractor | twenty-40 | 30-45 | forty-fifty |
| Heavy Responsibility Flail Mower | ||||
| Model | AGH140 | AGH160 | AGH180 | AGH200 |
| Proportions(LxWxH) | 1800x1850x1020mm | 1820x2050x1020mm | 1800x2250x1020mm | 1820x2450x1020mm |
| Structure weight(kg) | 564 | 590 | 618 | 648 |
| Slicing width(mm) | 1400 | 1600 | 1800 | 2000 |
| Working performance | 6000-160000m²/h | |||
| PTO speed | 540r/min | |||
| PTO spline | 6x8x1600mm | |||
| Tractor HP | 40-85 | 50-ninety | sixty-90 | 65-100 |
| ATV Finishing Mower | ||
| Model | ATFM120 | ATFM150 |
| Functioning width(mm) | 1200 | 1500 |
| Composition bodyweight(kg) | 210 | 250 |
| PTO speed | 540r/min | |
| No. of blades | 6 | 6 |
| Electric powered start off | Of course | Of course |
| Engine HP | 16HP (LONCIN) | |
| Ending Mower | |||
| Model | FMH120 | FMH150 | FMH180 |
| Cutting width(mm) | 1200 | 1500 | 1800 |
| Oil flow | 30L/min | ||
| Motor | 30cc | ||
| Working pressure | 20Mpa | ||
| Blade No. | 3pcs | ||
| Weight(kg) | 242 | 271 | 295 |
| Flail Collector | ||
| Design | FCN120 | FCN160 |
| Stucture bodyweight(kg) | 323 | 367 |
| Working width(mm) | 1150 | 1550 |
| Capacity | .55m³ | .7m³ |
| PTO velocity | 540r/min | |
| Flail sort | Y blade | |
| No. of flails | 56 | 72 |
| Tractor HP | 20-40 | 28-50 |
| Weighty Obligation Flail Mower | |||||||
| Design | KDK170 | KDK180 | KDK190 | KDK200 | KDK210 | KDK220 | KDK240 |
| Dimension(mm) | 1700x915x580 | 1800x915x580 | 1900x915x580 | 2000x915x580 | 2100x915x580 | 2200x915x580 | 2280x915x580 |
| Framework excess weight(kg) | 450 | 470 | 490 | 510 | 525 | 540 | 560 |
| Slicing width(mm) | 1700 | 1800 | 1900 | 2000 | 2100 | 2200 | 2400 |
| No. of hammers | 28 | 28 | 28 | 32 | 32 | 38 | 38 |
| PTO velocity | 540r/min | ||||||
| PTO spline | 6x8x1600mm | ||||||
| Tractor HP | forty five-65 | 55-90 | sixty-90 | 70-one hundred | 70-100 | 80-120 | eighty-a hundred and twenty |
| Prime Mower | ||||
| Design | TM110 | TM140 | TM160 | TM170 |
| Composition weight(kg) | 175 | 205 | 215 | 225 |
| Cutting fat(mm) | 1060 | 1360 | 1560 | 1660 |
| Equipment Box | 40hp | |||
| PTO velocity | 540r/min | |||
| Tractor HP | 18-twenty five | 20-35 | 25-40 | thirty-50 |
| Large Responsibility Flail Mower | |||||||
| Model | TOL105 | TOL115 | TOL125 | TOL135 | TOL145 | TOL155 | TOL165 |
| Slicing width(mm) | 1050 | 1150 | 1250 | 1350 | 1450 | 1550 | 1650 |
| Achieve angle up | 90° | ||||||
| Achieve angle down | 55° | ||||||
| PTO | 540r/min | ||||||
| Tractor HP | 18-twenty five | 25-45 | 35-sixty five | ||||
| Weighty Obligation Flail Mower | |||
| Model | TOS185 | TOS205 | TOS225 |
| Cutting width(mm) | 1850 | 2050 | 2250 |
| Reach angle up | 90° | ||
| Reach angle down | 55° | ||
| PTO | 540r/min | ||
| Tractor HP | fifty five-eighty five | ||
| Prime Mower | ||||
| Design | DS4FT | DS5FT | DS6FT | DS7FT |
| Dimension(mm) | 1320x1220x980 | 1624x1524x980 | 1929x1829x980 | 2234x2134x980 |
| Construction fat(kg) | a hundred and seventy | 220 | 240 | 260 |
| Chopping width(mm) | 1180 | 1484 | 1789 | 2094 |
| Operating efficiency | 3500-9500m²/h | 4400-12000m²/h | 5300-14000m²/h | 6200-16700m²/h |
| PTO speed | 540r/min | |||
| PTO spline | 6x8x1000mm | |||
| Tractor HP | 20-35 | twenty five-40 | forty-70 | sixty-100 |
| Tractor Trimmer | |
| Design | TS80 |
| Functioning width | 800mm |
| Blade | x2 |
| Hydraulic motor | 25cc(created-in force limiter) |
| Oil circulation | At minimum 30L/min |
| Tractor | 25-35HP |
| Packing dimensions | 1600x950x500mm |
| Fat | 197kg |
Q: Are you manufacturing unit or buying and selling company?
A) We are ISO9001 qualified manufacturing unit, primarily manufacture in Forestry & Farm Equipment.
B) Using “Self-made Self-advertising and marketing” organization, lowering the value of intermediate back links.
Q: What is your organization advantages?
A) As the foremost manufacturer of forest machines, we have exported to European marketplace for much more than ten several years, familiar with forest and farm market and can suggest to consumers appropriate products.
B) We have various products and can provide all the devices and tools in the forest and farm. You can get all the products you require. Straightforward and convenient for you.
C) With us your money and your enterprise is secure. We can provide seven-days refund in scenario of undesirable quality.
D) Coming with each other is a beginning retaining jointly is progress operating with each other is accomplishment.
Q: Can we acquire a single sample?
Sure, we want to incorporate sample charge to the cost and will return it back to your after obtaining your big order in foreseeable future.
Q: What’s your supply time?
Soon after acquiring your payment, we begin to create your purchase. It normally requires about fifteen-45 days dependent on the goods you get.
Q: How do you management your good quality?
To guarantee higher quality and productive management, we have handed ISO9001 high quality administration technique certificate. All of our merchandise are a hundred% inspected before shipment. Our entire manufacturing procedures are beneath a really significant and rigid system in our company.
Q: What’s your merchandise guarantee?
The warranty time of the machine is 1 year. Throughout this period, we will send out you the substitution for the damaged portion(not man created).
To satisfy the each and every demand of customer is our goal. We are standing by for any concern of buyer. We consider to make our support rapidly, effective and content.
Q: What’s your company mostly exporting industry?
We primarily export to European, North American, Australia, English and Southeast Asia Marketplace. Due to the fact of excellent quality and support, we have establish great and extended business relations with a lot of customers. Welcome clientele from all above the entire world to go to our manufacturing facility.
The use of original gear manufacturer’s (OEM) part numbers or trademarks , e.g. CASE® and John Deere® are for reference functions only and for indicating solution use and compatibility. Our business and the detailed substitute elements contained herein are not sponsored, accredited, or produced by the OEM.
